From d9a6855948fad17fa0fbc2017ab2be0238ca8b72 Mon Sep 17 00:00:00 2001 From: Mohammad Akhlaghi Date: Sat, 9 Jan 2021 01:34:15 +0000 Subject: IMPORTANT: analysis outputs written in BDIR/analysis Until now, the build directory contained a 'software/' directory (that hosted all the built software), a 'tex/' subdirectory for the final building of the paper, and many other directories containing intermediate/final data of the specific project. But this mixing of built software and data is against our modularity and minimal complexity principles: built software and built data are separate things and keeping them separate will enable many optimizations. With this commit, the build directory of the core Maneage branch will only contain two sub-directories: 'software/' and 'analysis/'. The 'software/' directory has the same contents as before and is not touched in this commit. However, the 'analysis/' directory is new and everything created in the './project make' phase of the project will be created inside of this directory. To facilitate easy access to these top-level built directories, two new variables are defined at the top of 'initialize.mk': 'badir', which is short for "built-analysis directory" and 'bsdir', which is short for "built-software directory". HOW TO IMPLEMENT THIS CHANGE IN YOUR PROJECT. It is easy: simply replace all occurances of '$(BDIR)' in your project's subMakefiles (except the ones below) to '$(badir)'. To confirm if everything is fine before building your project from scratch after merging, you can run the following command to see where 'BDIR' is used and confirm the only remaning cases. $ grep -r BDIR reproduce/analysis/* --> make/verify.mk: innobdir=$$(echo $$infile | sed -e's|$(BDIR)/||g'); \ --> make/initialize.mk:badir=$(BDIR)/analysis --> make/initialize.mk:bsdir=$(BDIR)/software --> make/initialize.mk: $$sys_rm -rf $(BDIR) --> make/top-prepare.mk:all: $(BDIR)/software/preparation-done.mk 'BDIR' should only be present in lines of the files above. If you see '$(BDIR)' used anywhere else, simply change it to '$(badir)'. Ofcourse, if your project assumes BDIR in other contexts, feel free to keep it, it will not conflict. If anything un-expected happens, please post a comment on the link below (you need to be registered on Savannah to post a comment): https://savannah.nongnu.org/task/?15855 One consequence of this change is that the 'analysis/' subdirectory can be optionally mounted on a separate partition. The need for this actually came up for some new users of Maneage in a Docker image. Docker can fix portability problems on systems that we haven't yet supported (even Windows!), or had a chance to fix low-level issues on. However, Docker doesn't have a GUI interface. So to see the built PDF or intermediate data, it was necessary to copy the built data to the host system after every change, which is annoying during working on a project. It would also need two copies of the source: one in the host, one in the container. All these frustrations can be fixed with this new feature. To describe this scenario, README.md now has a new section titled "Only software environment in the Docker image". It explains step-by-step how you can make a Docker image to only host the built software environment. While your project's source, software tarballs and 'BDIR/analysis' directories are on your host operating system. It has been tested before this commit and works very nicely. --- reproduce/software/make/basic.mk | 2 +- reproduce/software/make/high-level.mk | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'reproduce/software/make') diff --git a/reproduce/software/make/basic.mk b/reproduce/software/make/basic.mk index 58ebdb2..9217ee9 100644 --- a/reproduce/software/make/basic.mk +++ b/reproduce/software/make/basic.mk @@ -48,7 +48,7 @@ include reproduce/software/config/checksums.conf include reproduce/software/config/urls.conf # Basic directories -lockdir = $(BDIR)/locks +lockdir = $(BDIR)/software/locks tdir = $(BDIR)/software/tarballs ddir = $(BDIR)/software/build-tmp idir = $(BDIR)/software/installed diff --git a/reproduce/software/make/high-level.mk b/reproduce/software/make/high-level.mk index 948b23a..d69722e 100644 --- a/reproduce/software/make/high-level.mk +++ b/reproduce/software/make/high-level.mk @@ -43,7 +43,7 @@ include reproduce/software/config/TARGETS.conf include reproduce/software/config/texlive-packages.conf # Basic directories (similar to 'basic.mk'). -lockdir = $(BDIR)/locks +lockdir = $(BDIR)/software/locks tdir = $(BDIR)/software/tarballs ddir = $(BDIR)/software/build-tmp idir = $(BDIR)/software/installed -- cgit v1.2.1